|
Trend 90 degree trimmer T46/01 x 1/4" Shank
|
For trimming and bevelling timber, lippings and plastic laminate edges or any shaping applications.
Self-guiding trimmer with bearings mounted on end of cutter.
For trimming plastic or plywood overlay.
For copy profiling, use the bearing to follow a template or base edge of board.
A 3mm approximate overlap should be left before copy profiling.
When using plastic laminate always allow laminate adhesive to dry before trimming.
This avoids clogging the guide bearing.
Product available from stock
Sizes
D = 1/2" (12.7mm)
C = 25mm
B = 12.7mm
A = 90 degrees
Shank diameter = 1/4"
Product Reference
T46/01X1/4TC
|
|
£15.18
|
|
|
|
|
|
Trend Biscuit Jointer Set 342 x 1/4" Shank
|
For biscuit jointing of timber, man-made fibre and particle board with the router. The set includes three sizes of bearing which set the correct depth of cut for the three sizes available. A slightly longer cut than the length of the biscuit is required to allow some lateral play for easy alignment during assembley. A water based glue (PVA) is used with the biscuits which will expand as the moisture is absorbed. Boards are simply clamped together until glue is cured. For larger boards, biscuits can be doubled up by making two passes.
Product available from stock
Sizes
D = 40mm
C = 4mm
B = 15mm
B2 = 19mm
B3 = 23mm
Shank diameter = 1/4"
Product reference
342X1/4TC
|
|
£35.95
|
|
|
|
|
|
Trend BSC/10/100 Biscuits
|
Biscuit joining has proven to be one of the strongest, fastest, safest and most accurate ways to join hard and soft woods, plywood, composition boards etc.
Compared to dowelling, biscuit joinery is faster and more precise.
The biscuits are made of laminated beech which is then compressed before being die cut.
Beechwood biscuits expand up to 20 per cent when in contact with a woodworking adhesive. (e.g. PVA Glue).
Size. No.10.
Packed in 100.
Size; 53mm x 19mm x 4mm
|
|
£6.40
|
|
|
|
|
|
Trend Radius Cutter 12/5 x 1/4" Shank
|
For coves and part of a rule joint
Products available from Stock
Sizes
D = 10mm
C = 18mm
R = 5mm
Shank diameter = 1/4"
Product reference
12/5X1/4TC (Radius Cutter 10mm)
|
|
£20.65
|
|
|
|
|
|
Trend Template Profiler 46/95 x 1/4" Shank
|
Profiler with shank mounted bearing guides.
For use with router mounted above or below a table when following a template. For profiling and rebating applications only. Not for plunge cutting/grooving. A 3mm maximum overlap should be left before trimming. Refs. 46/910 and 46/91 have a shorter cutter length for use on thin boards. They are ideal for template making
Product available from stock
Sizes
D = 1/2" (12.7mm)
C = 1" (25.4mm)
B = 12.7mm
A = 90 degrees
Shank diameter = 1/4"
Product reference
46/95X1/4TC
|
|
£20.65
|
|
|
|
|
|
Trend Trimmer 46/80 x 1/4" Shank
|
Self-guiding triple flute cutter.
Extra fine trimming and longer life.
For trimming of laminate or plywood overlay etc
Product available from stock
Sizes
D = 1/2" (12.7mm)
C = 25.4mm
B = 12.7mm
Shank diameter = 1/4"
Product Reference
46/80X1/4TC
|
|
£17.85
|
|
|
|
|
|
Trend Two Flute Cutter 3/01 x 1/4" Shank
|
Use TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. All cutters above and including 9.5mm diameter, have TCT plunge centre tips.
Product available from stock
Sizes
D= 5/32" (4mm)
C = 11mm
Overall length = 51mm
Shank diameter = 1/4"
Product Reference
3/01X1/4TC
|
|
£12.45
|
|
|
|
|
|
Trend Two Flute Cutter 3/1 x 1/4" Shank
|
Use TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. All cutters above and including 9.5mm diameter, have TCT plunge centre tips.
Product available from stock
Sizes
D = 13/64" (5mm)
C = 16mm
Overall length = 56mm
Shank diametre = 1/4"
Product Reference
3/1X1/4TC
|
|
£14.05
|
|
|
|
|
|
Trend Two Flute Cutter 3/10 x 1/4" Shank
|
Use TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. All cutters above and including 9.5mm diameter, have TCT plunge centre tips.
Product available from stock
D = 1/8" (3.2mm)
C = 11mm
Overall length = 51mm
Shank diameter = 1/4"
Product Reference
3/10X1/4TC
|
|
£12.45
|
|
|
|
|
|
Trend Two Flute Cutter 3/2 x 1/4" Shank
|
Use TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. All cutters above and including 9.5mm diameter, have TCT plunge centre tips.
Product available from stock
Sizes
D = 15/64" (6mm)
C = 16mm
Overall length = 48mm
Shank diameter = 1/4"
Product Reference
3/2X1/4TC
|
|
£14.85
|
|
|
|
|
|
Trend Two Flute Cutter 3/50 x 1/4" Shank
|
Use TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. All cutters above and including 9.5mm diameter, have TCT plunge centre tips.
Product available from stock
Sizes
D = 3/8" (9.5mm)
C = 25mm
Overall length = 58mm
Shank diameter = 1/4"
Product Reference
3/50X1/4TC
|
|
£16.15
|
|
|
|
|
|
Trend Two Flute Cutter 3/6 x 1/2" Shank
|
Use TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics. Two flutes give a clean finish to cut edges. All cutters above and including 9.5mm diameter, have TCT plunge centre tips.
Product available from stock
Sizes
D = 25/64" (10mm)
C = 19mm
Overall length = 63mm
Shank diameter = 1/2"
Product Reference
3/6X1/2TC
|
|
£15.25
|
|
|
|
|
